TPR Valve Replacement
The T&P valve opens around 210°F or 150 psi — it is the tank's last line of defense. We find out whether a dripping valve is worn out or warning you…
Fuel safety first
A leaking gas water heater adds one non-negotiable rule to every repair: the gas goes off before work begins, and nothing returns to service until burner, pilot or igniter, flue venting, and gas connections are all verified safe. We repair the water-side leak — valves, fittings, tank connections — then run the full safety check before relighting. You also leave knowing your unit's warning signs, so the next issue gets caught early. Certified Professional, Licensed & Insured Team.

About this service
Water and gas systems share the same cabinet, so we treat every gas leak call as two jobs: stop the water, and confirm the fuel side is sound. After the gas valve is closed, we repair or replace the leaking water-side components — drain valves, T&P valves, fittings, tank connections — using parts rated for your unit. Then comes the part that matters most: checking the burner assembly, venting draft, and gas connections before the pilot is ever relit.
Serving Wheaton, IL 60187 and surrounding neighborhoods, we also use the visit to make you a sharper observer of your own heater: what a healthy burner flame looks like, where to sniff-test for gas, and which water warning signs to act on. Prevention is a habit, and habits start with knowing what to look at. Call (833) 713-2101.

How it works
We close the gas valve and the cold-water supply, then confirm the work area is safe before any repair begins.
We trace the water to its origin — fitting, valve, or tank — while keeping the fuel side undisturbed.
We explain the water-side failure, the repair, and the safety checks that will happen before relighting.
The leak is repaired, then the burner, pilot or igniter, venting, and gas connections are all verified before relight.
We show you the water-side warning signs and the simple gas-safety glances that belong in your seasonal routine.
FAQ
The water itself is the same nuisance as any leak, but standing water near a gas burner, pilot assembly, and electrical igniter adds real risk — including pilot outages and corrosion of gas controls. Shut off the gas and the water supply, and let a professional handle both sides.
Yes. Turn the gas valve on the unit to off, close the cold-water supply, and for extra safety you can switch off the unit's electrical supply too. Then call a professional — relighting and safety checks are not DIY steps.
Water often damages the pilot assembly, thermocouple, or igniter, or leaves the burner rusted and unreliable. A professional needs to inspect and usually replace the affected gas controls before relighting — forcing it risks an unsafe burner.
Related services
The T&P valve opens around 210°F or 150 psi — it is the tank's last line of defense. We find out whether a dripping valve is worn out or warning you…
Plastic drain valves crack and stop sealing, usually discovered during the flush that was overdue. We swap failed valves for solid brass that seals…
Top-of-tank fittings loosen and corrode over years of heat cycling — the kind of thing a seasonal glance would catch. We reseat or replace weeping…
Tankless units skip the tank but keep the leak points: condensate drains, isolation valves, heat exchanger seals. We trace and fix them, then set up…
Every tank eventually leaks — the question is where the water goes. We fit a properly sized pan with a real drain line, and add a leak alarm so the…
Electric units leak from element gaskets plus the usual fittings and valves. We cut power at the breaker, replace failed gaskets and components, and…
A failed expansion tank turns every heating cycle into a pressure spike that pops T&P valves and strains fittings. We test bladder and air charge,…
Old gate valves seize or fail to close fully — exactly when you need them most. We install quarter-turn ball valves that close positively, and show…
Burst fittings, flooding garages, tanks discharging heavily — some leaks can't wait. We stop the water first, complete a lasting repair, and talk…
When a tank has failed internally, we replace it with a correctly sized unit — proper connections, venting, and expansion control — plus the…